If you came here looking for something else please go to the site map
 

    The following are standard hvac. prices that we charge in most situations.
    The purpose of this list is so that we won't have to re invent the wheel each time since most systems require pretty much the same things.
    While these prices may seem high please consider that I sometimes start my day at 8 or 9 am working outside in the heat and humidity and don't get to bed until 1 or 2 am after reading catalogs and books and even then try to solve problems in my sleep. Then have to do it all again the next day.
  Thanks   Scott Meenen N3SJH 

    Clean standard Gas furnace $100.00  (contact us for explanation)

    Change condenser fan motor on 1.5 to 5 ton heat pump or air conditioner most units.
(more for double shaft motors) $250.00

    Change Gas valve on furnace, boiler or pool heater (standing pilot only) including any pipe fittings and a new thermocouple with pilot tubing. $300.00

    Change Gas valve on furnace, boiler or pool heater intermittent pilot or proven pilot including any pipe fittings and  new pilot tubing.  $350.00

    Change Gas valve on furnace, boiler or pool heater from Millivolt to standard standing pilot including any pipe fittings, thermocouple and  new pilot tubing.  $350.00

    Change Gas valve on furnace, boiler or pool heater from Millivolt to intermittent pilot or direct spark including Ignition module wiring and any pipe fittings and  new pilot tubing.  $550.00

    Change Gas valve on furnace, boiler or pool heater from standing pilot to intermittent pilot or direct spark including Ignition module wiring and any pipe fittings and  new pilot tubing.  $550.00 (this is for gas equipment where lighting the pilot is a nuisance and you have problems with wind such as an outdoor pool heater)

    Change Gas valve on furnace, boiler or pool heater hot surface ignitor (HSI), direct spark  $350.00

    Change induced draft fan motor on furnaces ,boilers ; Carrier, Bryant, Comfortmaker, Goodman, Janitrol, Lennox (Armstrong, Air ease), Trane (American Standard), Heil, Tempstar, Miller, Intertherm, Rheem/Ruud,  Weil Mclain. $300.00 if we can get a replacement motor. $400 If we need to buy a whole unit to fit that particular furnace.

    Change standard compressor 1.5 to 5 tons including any minor re piping and any additional refrigerant. (Does not include GE/Trane/American Standard) $450.00

    Change compressor on a GE/Trane/American Standard 1.5 to 5 tons.. Does not include any re- piping but does include additional refrigerant and replacing wires and terminals $1100.00
 For a pre writtten quote follow this link.

    Electrical tune-up single phase heat pump or air conditioner;
Replace contactor, add hard start kit, replace any damaged wiring and terminals $120.00

    Replace contactor single phase heat pump or air conditioner; $50.00

    Replace contactor three phase heat pump or air conditioner; $75.00
 

    Mechanical tune-up install liquid line sight glass and dryer. liquid line service valve $165.00

    Mechanical tune-up install liquid line sight glass and dryer. liquid line service valve, High and low pressure controls $300.00

    Mechanical tune-up install liquid line sight glass and dryer on unit already equipped with a liquid line service valve $100.00

    Mechanical tune-up change indoor coil to a larger coil with thermostatic expansion valve including one of above two plus hard start kit if unit is not already equipped (necessary for installation) plus minor sheet metal modifications $650.00

    Mechanical tune-up to add thermostatic expansion valves inside and out to a heat pump plus hard start kit if unit is not already equipped (necessary for installation) plus minor clean up of wiring and some small piping modifications $650.00

 Go to or return to the G&S mechanical home page:
For a list of all files on this site go to the sitemap.